Expose charging session elapsed time in monitoring packet (v1.0.27).

CONN.ChargingTime ticks at 1 Hz during Charging; serial GET_STATUS reports elapsed min/sec instead of zero stubs.

Co-authored-by: Cursor <cursoragent@cursor.com>

Core/Inc/charger_config.h

@@ -9,7 +9,24 @@
 
 #define PSU_NUM 1
 
-/* Everest / стенд: запрос «500 В» на шине — реально на PSU задаются U/I ниже; статус может оставаться 500 В (serial.c). */
-#define FAKE_EVREQ_VOLTAGE_V    500u
-#define FAKE_PSU_VOLTAGE_V      300u
-#define FAKE_PSU_CURRENT_0P1A    10u
+/* Dynamic LV clamp (CS60 hv_limit): active only on overload at low bus voltage. */
+#define PSU_LV_CLAMP_V              499u
+#define PSU_HV_LIMIT_ON_THRESHOLD   480u
+#define PSU_HV_LIMIT_OFF_THRESHOLD  495u
+#define PSU_HV_SWITCH_DELAY_MS      1000u
+#define PSU_HV_LOAD_CURRENT         300u   /* 30.0 A, MeasuredCurrent is 0.1 A/bit */
+#define PSU_HV_LIMIT_MAX_COUNT      3u
+
+/* Fast discharge: PSU off/on cycle on step-down setpoint (unloaded bus). */
+#define PSD_ENABLE                    1u
+#define PSD_MAX_CMD_CURRENT_0P1A      20u   /* 2.0 A */
+#define PSD_MAX_MEASURED_CURRENT_0P1A   30u   /* 3.0 A */
+#define PSD_MEASURED_LATCH_MS         500u
+#define PSD_MIN_VOLTAGE_STEP_V        50u
+#define PSD_DISCHARGE_MARGIN_V        15u
+#define PSD_DEBOUNCE_MS               2000u
+#define PSD_MAX_PER_SESSION           4u
+#define PSD_OFF_TIMEOUT_MS            10000u /* как PSU_WAIT_ACK_OFF */
+#define PSD_ON_TIMEOUT_MS             10000u
+#define PSD_ON_RETRY_MS               500u   /* повтор SET+ON в ON_WAIT */
+#define PSD_PRECHARGE_TOLERANCE_V     40u   /* ~±10% for 350 V precharge window */

Core/Inc/charger_control.h

@@ -68,6 +68,10 @@ typedef struct{
 	uint16_t WantedCurrent; //0.1A/bit
 	CONN_Error_t chargingError; // 0 if okay
 	uint8_t EvConnected;
+	uint32_t ChargingTime; // seconds of active charging in current session
+	uint8_t hv_limit;        // Limits PSU voltage to LV range when set
+	uint32_t hv_tick;        // Timer for delayed HV limit switching
+	uint8_t hv_limit_count;  // Anti-chatter counter for LV limit switching
 
 } ChargingConnector_t;
 
@@ -79,3 +83,4 @@ extern ChargingConnector_t CONN;
 
 void CONN_Init();
 void CONN_Loop();
+void CONN_GetElapsedForMonitoring(uint16_t *min, uint8_t *sec);

Core/Inc/main.h

@@ -27,7 +27,7 @@ extern "C" {
 /* USER CODE BEGIN EC */
 #define FW_VERSION_MAJOR 1
 #define FW_VERSION_MINOR 0
-#define FW_VERSION_PATCH 19
+#define FW_VERSION_PATCH 27
 /* USER CODE END EC */
 
 /* Exported macro ------------------------------------------------------------*/

Core/Inc/power_setpoint_executor.h

@@ -0,0 +1,21 @@
+#pragma once
+
+#include <stdint.h>
+
+#include "power_setpoint_policy.h"
+
+typedef enum {
+	PSD_TRY_IDLE = 0,
+	PSD_TRY_APPLIED_NORMAL,
+	PSD_TRY_START_FAST_DISCHARGE,
+} PowerSetpointTryResult_t;
+
+void PowerSetpoint_Init(void);
+void PowerSetpoint_OnCommand(uint16_t voltage_V, uint16_t current_0p1A);
+void PowerSetpoint_UpdateDeliveryLatch(void);
+uint8_t PowerSetpoint_HasPending(void);
+uint8_t PowerSetpoint_IsBusy(void);
+PowerSetpointTryResult_t PowerSetpoint_TryApply(void);
+void PowerSetpoint_GetFastDischargeTarget(PowerSetpoint_t *target);
+void PowerSetpoint_OnFastDischargeComplete(void);
+void PowerSetpoint_OnFastDischargeAbort(void);

Core/Inc/power_setpoint_policy.h

@@ -0,0 +1,35 @@
+#pragma once
+
+#include <stdint.h>
+
+#include "charger_config.h"
+
+typedef struct {
+	uint16_t voltage_V;
+	uint16_t current_0p1A;
+} PowerSetpoint_t;
+
+typedef enum {
+	POWER_SETPOINT_NORMAL,
+	POWER_SETPOINT_FAST_DISCHARGE,
+} PowerSetpointAction_t;
+
+typedef struct {
+	uint8_t  dc_contactor_closed;
+	uint8_t  psu_hv_enabled;
+	uint16_t measured_voltage_V;
+	uint16_t measured_current_0p1A;
+	uint8_t  power_delivery_active;
+	uint8_t  enable_output;
+	uint8_t  psu_state_connected;
+	uint8_t  psu_cont_fault;
+	uint8_t  psu_fault;
+	uint8_t  fast_discharge_count;
+	uint32_t last_fast_discharge_ms;
+	uint32_t now_ms;
+} PowerPathContext_t;
+
+PowerSetpointAction_t PowerSetpoint_Decide(
+	const PowerSetpoint_t *applied,
+	const PowerSetpoint_t *next,
+	const PowerPathContext_t *ctx);

Core/Inc/psu_control.h

@@ -5,6 +5,7 @@
 
 void PSU_Init();
 void PSU_Enable(uint8_t addr, uint8_t enable);
+void PSU_SetVoltageCurrent(uint8_t addr, uint16_t voltage, uint16_t current);
 void PSU_ReadWrite(void);
 
 // --- Состояние силового модуля (DC30, один PSU) ---
@@ -16,6 +17,11 @@ typedef enum{
 	PSU_WAIT_ACK_ON,       // ждём подтверждение включения модуля (напряжение выше порога)
 	PSU_CONT_WAIT_ACK_ON,  // включаем DC-контактор и ждём подтверждение
 	PSU_CONNECTED,         // модуль включён, DC-контактор замкнут
+	PSU_FAST_DISCHARGE_OFF,
+	PSU_FAST_DISCHARGE_WAIT,      /* ждём подтверждение выключения (как PSU_WAIT_ACK_OFF) */
+	PSU_FAST_DISCHARGE_SET,       /* задать целевое U/I при выключенном модуле */
+	PSU_FAST_DISCHARGE_ON,        /* команда включения после set */
+	PSU_FAST_DISCHARGE_ON_WAIT,   /* ждём подтверждение включения (как PSU_WAIT_ACK_ON) */
 	PSU_CURRENT_DROP,      // снижение тока перед отключением
 	PSU_WAIT_ACK_OFF,      // ждём подтверждение выключения модуля (напряжение ниже порога)
 	PSU_CONT_WAIT_ACK_OFF, // выключаем DC-контактор и ждём подтверждение
@@ -78,8 +84,6 @@ typedef struct {
 
 	// Дополнительные параметры для одного модуля DC30
 	uint32_t power_limit;    // лимит мощности [кВт]
-	uint8_t  hv_mode;        // HV-режим (ограничение напряжения)
-	uint32_t hv_tick;        // таймер для задержки входа в HV-режим
 
 	uint32_t tempAmbient;    // температура окружающего воздуха (из PSU_04)
 	union { uint8_t raw; PSU_Status0_t bits; } status0;  // modularForm0

Core/Src/charger_control.c

@@ -13,10 +13,15 @@ void CONN_Init(){
 	CONN.connControl = CMD_NONE;
 	CONN.connState   = Unknown;
 	CONN.RequestedVoltage = PSU_MIN_VOLTAGE;
+	CONN.ChargingTime = 0;
+	CONN.hv_limit = 0u;
+	CONN.hv_tick = 0u;
+	CONN.hv_limit_count = 0u;
 
 }
 
 void CONN_Loop(){
+	static uint32_t charging_time_tick = 0;
     static CONN_State_t last_connState = Unknown;
 	if(last_connState != CONN.connState){
 		last_connState = CONN.connState;
@@ -37,6 +42,25 @@ void CONN_Loop(){
 		log_printf(LOG_WARN, "CONN0 Error: %d\n", (int)CONN.chargingError);
 	}
 
+	if (HAL_GetTick() - charging_time_tick >= 1000U) {
+		charging_time_tick += 1000U;
+		if (CONN.connState == Charging) {
+			CONN.ChargingTime++;
+		}
+		if (CONN.connState == Unplugged) {
+			CONN.ChargingTime = 0;
+		}
+	}
+}
+
+void CONN_GetElapsedForMonitoring(uint16_t *min, uint8_t *sec) {
+	uint32_t elapsed_sec = CONN.ChargingTime;
+	if (min != NULL) {
+		*min = (uint16_t)(elapsed_sec / 60U);
+	}
+	if (sec != NULL) {
+		*sec = (uint8_t)(elapsed_sec % 60U);
+	}
 }
 
 void CONN_SetState(CONN_State_t state){

Core/Src/power_setpoint_executor.c

@@ -0,0 +1,196 @@
+#include "power_setpoint_executor.h"
+
+#include "charger_config.h"
+#include "charger_control.h"
+#include "debug.h"
+#include "psu_control.h"
+#include "serial.h"
+
+static PowerSetpoint_t applied;
+static PowerSetpoint_t pending;
+static PowerSetpoint_t fd_target;
+static uint8_t setpoint_dirty;
+static uint8_t fd_active;
+static uint8_t power_delivery_latched;
+static uint8_t fast_discharge_count;
+static uint32_t last_fast_discharge_ms;
+static uint32_t measured_high_current_since_ms;
+
+static uint8_t session_ended_state(CONN_State_t state)
+{
+	return (state == Unknown) || (state == Unplugged) || (state == Finished) ||
+	       (state == FinishedEV) || (state == FinishedEVSE);
+}
+
+void PowerSetpoint_Init(void)
+{
+	applied.voltage_V = PSU_MIN_VOLTAGE;
+	applied.current_0p1A = 0u;
+	pending = applied;
+	fd_target = applied;
+	setpoint_dirty = 0u;
+	fd_active = 0u;
+	power_delivery_latched = 0u;
+	fast_discharge_count = 0u;
+	last_fast_discharge_ms = 0u;
+	measured_high_current_since_ms = 0u;
+}
+
+void PowerSetpoint_OnCommand(uint16_t voltage_V, uint16_t current_0p1A)
+{
+#if PSD_ENABLE
+	pending.voltage_V = voltage_V;
+	pending.current_0p1A = current_0p1A;
+	setpoint_dirty = 1u;
+#else
+	(void)voltage_V;
+	(void)current_0p1A;
+#endif
+}
+
+void PowerSetpoint_UpdateDeliveryLatch(void)
+{
+#if PSD_ENABLE
+	uint32_t now = HAL_GetTick();
+
+	if (!CONN.EnableOutput || !CONN.EvConnected || session_ended_state(CCS_EvseState)) {
+		power_delivery_latched = 0u;
+		fast_discharge_count = 0u;
+		last_fast_discharge_ms = 0u;
+		measured_high_current_since_ms = 0u;
+		return;
+	}
+
+	if (CONN.WantedCurrent > PSD_MAX_CMD_CURRENT_0P1A) {
+		power_delivery_latched = 1u;
+	}
+
+	if (CCS_EvseState == Charging) {
+		power_delivery_latched = 1u;
+	}
+
+	if (CONN.MeasuredCurrent >= PSD_MAX_MEASURED_CURRENT_0P1A) {
+		if (measured_high_current_since_ms == 0u) {
+			measured_high_current_since_ms = now;
+		} else if ((now - measured_high_current_since_ms) >= PSD_MEASURED_LATCH_MS) {
+			power_delivery_latched = 1u;
+		}
+	} else {
+		measured_high_current_since_ms = 0u;
+	}
+#endif
+}
+
+uint8_t PowerSetpoint_HasPending(void)
+{
+#if PSD_ENABLE
+	return setpoint_dirty;
+#else
+	return 0u;
+#endif
+}
+
+uint8_t PowerSetpoint_IsBusy(void)
+{
+#if PSD_ENABLE
+	if (!fd_active) {
+		return 0u;
+	}
+	switch (PSU0.state) {
+	case PSU_FAST_DISCHARGE_OFF:
+	case PSU_FAST_DISCHARGE_WAIT:
+	case PSU_FAST_DISCHARGE_SET:
+	case PSU_FAST_DISCHARGE_ON:
+	case PSU_FAST_DISCHARGE_ON_WAIT:
+		return 1u;
+	default:
+		return 0u;
+	}
+#else
+	return 0u;
+#endif
+}
+
+static PowerPathContext_t build_context(void)
+{
+	PowerPathContext_t ctx;
+
+	ctx.dc_contactor_closed = PSU0.CONT_enabled;
+	ctx.psu_hv_enabled = PSU0.PSU_enabled;
+	ctx.measured_voltage_V = CONN.MeasuredVoltage;
+	ctx.measured_current_0p1A = (uint16_t)CONN.MeasuredCurrent;
+	ctx.power_delivery_active = power_delivery_latched;
+	ctx.enable_output = CONN.EnableOutput;
+	ctx.psu_state_connected = (PSU0.state == PSU_CONNECTED) ? 1u : 0u;
+	ctx.psu_cont_fault = PSU0.cont_fault;
+	ctx.psu_fault = PSU0.psu_fault;
+	ctx.fast_discharge_count = fast_discharge_count;
+	ctx.last_fast_discharge_ms = last_fast_discharge_ms;
+	ctx.now_ms = HAL_GetTick();
+	return ctx;
+}
+
+PowerSetpointTryResult_t PowerSetpoint_TryApply(void)
+{
+#if PSD_ENABLE
+	PowerPathContext_t ctx;
+	PowerSetpointAction_t action;
+
+	if (!setpoint_dirty || fd_active) {
+		return PSD_TRY_IDLE;
+	}
+
+	ctx = build_context();
+	action = PowerSetpoint_Decide(&applied, &pending, &ctx);
+
+	if (action == POWER_SETPOINT_FAST_DISCHARGE) {
+		fd_target = pending;
+		fd_active = 1u;
+		setpoint_dirty = 0u;
+		log_printf(LOG_INFO, "Fast discharge trigger %u->%u I=%u\n",
+		           (unsigned)applied.voltage_V,
+		           (unsigned)fd_target.voltage_V,
+		           (unsigned)fd_target.current_0p1A);
+		return PSD_TRY_START_FAST_DISCHARGE;
+	}
+
+	if (!PSU0.ready) {
+		return PSD_TRY_IDLE;
+	}
+
+	PSU_SetVoltageCurrent(0, pending.voltage_V, pending.current_0p1A);
+	applied = pending;
+	setpoint_dirty = 0u;
+	return PSD_TRY_APPLIED_NORMAL;
+#else
+	return PSD_TRY_IDLE;
+#endif
+}
+
+void PowerSetpoint_GetFastDischargeTarget(PowerSetpoint_t *target)
+{
+	if (target != 0) {
+		*target = fd_target;
+	}
+}
+
+void PowerSetpoint_OnFastDischargeComplete(void)
+{
+#if PSD_ENABLE
+	applied = fd_target;
+	fd_active = 0u;
+	fast_discharge_count++;
+	last_fast_discharge_ms = HAL_GetTick();
+	log_printf(LOG_INFO, "Fast discharge complete, V=%u\n", (unsigned)CONN.MeasuredVoltage);
+#endif
+}
+
+void PowerSetpoint_OnFastDischargeAbort(void)
+{
+#if PSD_ENABLE
+	fd_active = 0u;
+	pending = fd_target;
+	setpoint_dirty = 1u;
+	log_printf(LOG_WARN, "Fast discharge aborted, V=%u\n", (unsigned)CONN.MeasuredVoltage);
+#endif
+}

Core/Src/power_setpoint_policy.c

@@ -0,0 +1,77 @@
+#include "power_setpoint_policy.h"
+
+PowerSetpointAction_t PowerSetpoint_Decide(
+	const PowerSetpoint_t *applied,
+	const PowerSetpoint_t *next,
+	const PowerPathContext_t *ctx)
+{
+#if !PSD_ENABLE
+	(void)applied;
+	(void)next;
+	(void)ctx;
+	return POWER_SETPOINT_NORMAL;
+#else
+	uint16_t delta_v;
+
+	if (applied == 0 || next == 0 || ctx == 0) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (next->voltage_V >= applied->voltage_V) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	delta_v = (uint16_t)(applied->voltage_V - next->voltage_V);
+	if (delta_v < PSD_MIN_VOLTAGE_STEP_V) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (applied->current_0p1A > PSD_MAX_CMD_CURRENT_0P1A ||
+	    next->current_0p1A > PSD_MAX_CMD_CURRENT_0P1A) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->measured_current_0p1A >= PSD_MAX_MEASURED_CURRENT_0P1A) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->measured_voltage_V <= (uint16_t)(next->voltage_V + PSD_DISCHARGE_MARGIN_V)) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->power_delivery_active) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (!ctx->enable_output) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (!ctx->psu_state_connected) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (!ctx->dc_contactor_closed) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (!ctx->psu_hv_enabled) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->psu_cont_fault || ctx->psu_fault) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->fast_discharge_count >= PSD_MAX_PER_SESSION) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	if (ctx->last_fast_discharge_ms != 0u &&
+	    (ctx->now_ms - ctx->last_fast_discharge_ms) < PSD_DEBOUNCE_MS) {
+		return POWER_SETPOINT_NORMAL;
+	}
+
+	return POWER_SETPOINT_FAST_DISCHARGE;
+#endif
+}

Core/Src/psu_control.c

@@ -6,6 +6,7 @@
 #include "charger_control.h"
 #include "debug.h"
 #include "isr_opt.h"
+#include "power_setpoint_executor.h"
 #include <stdio.h>
 #include <string.h>
 
@@ -25,14 +26,165 @@ PSU_t PSU0;
 #define PSU_VOLTAGE_THRESHOLD 20 // Порог напряжения для определения состояния (В)
 #define PSU_ONLINE_TIMEOUT 500 // Таймаут для определения состояния (мс)
 #define PSU_STARTUP_DELAY 4000 // Задержка 2 секунды перед включением
+#define PSU_DIAG_LOG_MS 2000u
 
 uint32_t can_lastpacket;
 
 extern CAN_HandleTypeDef hcan2;
 
+static uint16_t psu_last_can_v;
+static uint16_t psu_last_can_i_0p1A;
+
 static void PSU_SendCmd(uint8_t source, uint8_t destination, uint8_t cmd, void *data);
 
+static const char *PSU_StateName(PSU_State_t state)
+{
+	switch (state) {
+	case PSU_UNREADY: return "UNREADY";
+	case PSU_INITIALIZING: return "INIT";
+	case PSU_READY: return "READY";
+	case PSU_WAIT_ACK_ON: return "WAIT_ON";
+	case PSU_CONT_WAIT_ACK_ON: return "CONT_ON";
+	case PSU_CONNECTED: return "CONNECTED";
+	case PSU_FAST_DISCHARGE_OFF: return "FD_OFF";
+	case PSU_FAST_DISCHARGE_WAIT: return "FD_WAIT";
+	case PSU_FAST_DISCHARGE_SET: return "FD_SET";
+	case PSU_FAST_DISCHARGE_ON: return "FD_ON";
+	case PSU_FAST_DISCHARGE_ON_WAIT: return "FD_ON_WAIT";
+	case PSU_CURRENT_DROP: return "CUR_DROP";
+	case PSU_CONT_WAIT_ACK_OFF: return "CONT_OFF";
+	case PSU_WAIT_ACK_OFF: return "WAIT_OFF";
+	case PSU_OFF_PAUSE: return "OFF_PAUSE";
+	default: return "?";
+	}
+}
+
+static void PSU_LogPeriodicDiag(void)
+{
+	static uint32_t last_log_ms;
+	uint32_t now = HAL_GetTick();
+	uint8_t block_setpoint;
+
+	if ((now - last_log_ms) < PSU_DIAG_LOG_MS) {
+		return;
+	}
+	last_log_ms = now;
+
+#if PSD_ENABLE
+	block_setpoint = PowerSetpoint_HasPending() || PowerSetpoint_IsBusy();
+#else
+	block_setpoint = 0u;
+#endif
+
+	log_printf(LOG_INFO,
+	           "PSU diag st=%s req=%uV/%u.%uA want=%uV/%u.%uA "
+	           "can=%uV/%u.%uA meas=%uV/%d.%uA "
+	           "enOut=%u out=%u rdy=%u on=%u cont=%u ac=%u hv=%u psd_blk=%u "
+	           "err=%u s0=0x%02x s1=0x%02x s2=0x%02x can_age=%lums\n",
+	           PSU_StateName(PSU0.state),
+	           (unsigned)CONN.RequestedVoltage,
+	           (unsigned)(CONN.RequestedCurrent / 10u),
+	           (unsigned)(CONN.RequestedCurrent % 10u),
+	           (unsigned)CONN.RequestedVoltage,
+	           (unsigned)(CONN.WantedCurrent / 10u),
+	           (unsigned)(CONN.WantedCurrent % 10u),
+	           (unsigned)psu_last_can_v,
+	           (unsigned)(psu_last_can_i_0p1A / 10u),
+	           (unsigned)(psu_last_can_i_0p1A % 10u),
+	           (unsigned)CONN.MeasuredVoltage,
+	           (int)(CONN.MeasuredCurrent / 10),
+	           (unsigned)(((CONN.MeasuredCurrent < 0) ?
+	                        -CONN.MeasuredCurrent : CONN.MeasuredCurrent) % 10),
+	           (unsigned)CONN.EnableOutput,
+	           (unsigned)CONN.outputEnabled,
+	           (unsigned)PSU0.ready,
+	           (unsigned)PSU0.PSU_enabled,
+	           (unsigned)PSU0.CONT_enabled,
+	           (unsigned)PSU0.enableAC,
+	           (unsigned)CONN.hv_limit,
+	           (unsigned)block_setpoint,
+	           (unsigned)CONN.chargingError,
+	           (unsigned)PSU0.status0.raw,
+	           (unsigned)PSU0.status1.raw,
+	           (unsigned)PSU0.status2.raw,
+	           (unsigned long)(can_lastpacket ? (now - can_lastpacket) : 9999u));
+}
+
+static void PSU_HvControl(void)
+{
+	if (CONN.EnableOutput == 0u) {
+		if ((CONN.hv_limit != 0u) || (CONN.hv_limit_count != 0u)) {
+			log_printf(LOG_INFO, "HV limit reset output off\n");
+		}
+		CONN.hv_limit = 0u;
+		CONN.hv_tick = 0u;
+		CONN.hv_limit_count = 0u;
+		return;
+	}
+
+	if (!PSU0.online) {
+		if ((CONN.hv_limit != 0u) || (CONN.hv_limit_count != 0u)) {
+			log_printf(LOG_INFO, "HV limit reset no PSU\n");
+		}
+		CONN.hv_limit = 0u;
+		CONN.hv_tick = 0u;
+		CONN.hv_limit_count = 0u;
+		return;
+	}
+
+	if (CONN.hv_limit == 0u) {
+		if ((CONN.hv_limit_count < PSU_HV_LIMIT_MAX_COUNT) &&
+		    (CONN.MeasuredVoltage < PSU_HV_LIMIT_ON_THRESHOLD) &&
+		    (CONN.MeasuredCurrent > PSU_HV_LOAD_CURRENT)) {
+			if (CONN.hv_tick == 0u) {
+				CONN.hv_tick = HAL_GetTick();
+			} else if ((HAL_GetTick() - CONN.hv_tick) >= PSU_HV_SWITCH_DELAY_MS) {
+				CONN.hv_limit = 1u;
+				CONN.hv_limit_count++;
+				CONN.hv_tick = 0u;
+				log_printf(LOG_WARN, "HV limit ON V=%d I=%d cnt=%d\n",
+				           (int)CONN.MeasuredVoltage,
+				           (int)CONN.MeasuredCurrent,
+				           (int)CONN.hv_limit_count);
+				if (CONN.hv_limit_count >= PSU_HV_LIMIT_MAX_COUNT) {
+					log_printf(LOG_WARN, "HV limit locked cnt=%d\n",
+					           (int)CONN.hv_limit_count);
+				}
+			}
+		} else {
+			CONN.hv_tick = 0u;
+		}
+	} else {
+		if ((CONN.MeasuredVoltage > PSU_HV_LIMIT_OFF_THRESHOLD) ||
+		    (CONN.MeasuredCurrent <= PSU_HV_LOAD_CURRENT)) {
+			if (CONN.hv_tick == 0u) {
+				CONN.hv_tick = HAL_GetTick();
+			} else if ((HAL_GetTick() - CONN.hv_tick) >= PSU_HV_SWITCH_DELAY_MS) {
+				CONN.hv_limit = 0u;
+				CONN.hv_tick = 0u;
+				log_printf(LOG_INFO, "HV limit OFF V=%d I=%d cnt=%d\n",
+				           (int)CONN.MeasuredVoltage,
+				           (int)CONN.MeasuredCurrent,
+				           (int)CONN.hv_limit_count);
+			}
+		} else {
+			CONN.hv_tick = 0u;
+		}
+	}
+}
+
 static void PSU_SwitchState(PSU_State_t state){
+	if (PSU0.state != state) {
+		log_printf(LOG_INFO,
+		           "PSU st %s->%s enOut=%u rdy=%u on=%u cont=%u err=%u\n",
+		           PSU_StateName(PSU0.state),
+		           PSU_StateName(state),
+		           (unsigned)CONN.EnableOutput,
+		           (unsigned)PSU0.ready,
+		           (unsigned)PSU0.PSU_enabled,
+		           (unsigned)PSU0.CONT_enabled,
+		           (unsigned)CONN.chargingError);
+	}
 	PSU0.state = state;
 	PSU0.statetick = HAL_GetTick();
 }
@@ -41,6 +193,24 @@ static uint32_t PSU_StateTime(void){
 	return HAL_GetTick() - PSU0.statetick;
 }
 
+static void PSU_FastDischarge_PushTarget(void)
+{
+	PowerSetpoint_t fd_sp;
+
+	PowerSetpoint_GetFastDischargeTarget(&fd_sp);
+	PSU_SetVoltageCurrent(0, fd_sp.voltage_V, fd_sp.current_0p1A);
+	PSU_Enable(0, 1);
+}
+
+static void PSU_FastDischarge_AbortToConnected(void)
+{
+	PowerSetpoint_OnFastDischargeAbort();
+	if (!PSU0.PSU_enabled) {
+		PSU_FastDischarge_PushTarget();
+	}
+	PSU_SwitchState(PSU_CONNECTED);
+}
+
 ISR_FAST void HAL_CAN_RxFifo1MsgPendingCallback(CAN_HandleTypeDef *hcan){
 
 	static CAN_RxHeaderTypeDef RxHeader;
@@ -150,10 +320,9 @@ void PSU_Init(){
 	PSU0.statetick = HAL_GetTick();
 
 	PSU0.power_limit = PSU_MAX_POWER; // kW
-	PSU0.hv_mode     = 0;
-	PSU0.hv_tick     = 0;
 
 	PSU_Enable(0, 0);
+	PowerSetpoint_Init();
 }
 
 void PSU_Enable(uint8_t addr, uint8_t enable){
@@ -183,7 +352,9 @@ void PSU_SetVoltageCurrent(uint8_t addr, uint16_t voltage, uint16_t current){
 
 	if(voltage<PSU_MIN_VOLTAGE) voltage = PSU_MIN_VOLTAGE;
 
-	if((PSU0.hv_mode==0) && voltage>499) voltage = 499;
+	if((CONN.hv_limit != 0u) && (voltage > PSU_LV_CLAMP_V)){
+		voltage = PSU_LV_CLAMP_V;
+	}
 
 	uint32_t current_ma = current * 100;
 	uint32_t voltage_mv = voltage * 1000;
@@ -198,6 +369,8 @@ void PSU_SetVoltageCurrent(uint8_t addr, uint16_t voltage, uint16_t current){
 	data.moduleVoltage[2] = (voltage_mv >>   8) & 0xFF;
 	data.moduleVoltage[3] = (voltage_mv >>   0) & 0xFF;
 
+	psu_last_can_v = voltage;
+	psu_last_can_i_0p1A = current;
 	PSU_SendCmd(0xF0, addr, 0x1C, &data);
 
 }
@@ -258,35 +431,50 @@ void PSU_ReadWrite(){
 	}
 	CONN.RequestedPower = CONN.RequestedCurrent * CONN.RequestedVoltage / 10;
 
-	if(PSU0.ready){
-		if (CONN.RequestedVoltage == FAKE_EVREQ_VOLTAGE_V) {
-			PSU_SetVoltageCurrent(0, (uint16_t)FAKE_PSU_VOLTAGE_V, (uint16_t)FAKE_PSU_CURRENT_0P1A);
-		}else{
-			PSU_SetVoltageCurrent(0, CONN.RequestedVoltage, CONN.RequestedCurrent); // Normal mode
-		}
-		ED_Delay(CAN_DELAY);
-		if(CONN.MeasuredVoltage > 490){
-			if(PSU0.hv_tick == 0){
-				PSU0.hv_tick = HAL_GetTick();
-			}else if((HAL_GetTick() - PSU0.hv_tick) >= 10000){
-				PSU0.hv_mode = 1;
-			}
-		}else{
-			PSU0.hv_tick = 0;
+#if PSD_ENABLE
+	{
+		uint8_t block_setpoint = PowerSetpoint_HasPending() || PowerSetpoint_IsBusy();
+
+		if (PSU0.ready && !block_setpoint) {
+			PSU_SetVoltageCurrent(0, CONN.RequestedVoltage, CONN.RequestedCurrent);
+			ED_Delay(CAN_DELAY);
 		}
 	}
+#else
+	if (PSU0.ready) {
+		PSU_SetVoltageCurrent(0, CONN.RequestedVoltage, CONN.RequestedCurrent); // Normal mode
+		ED_Delay(CAN_DELAY);
+	}
+#endif
 
-	// PSU_SetHVMode(0, PSU0.hv_mode); // auto set, no need
-	// ED_Delay(CAN_DELAY);
+	if (PSU0.ready) {
+		PSU_HvControl();
+	}
 
 }
 
 void PSU_Task(void){
 	static uint32_t psu_on_tick = 0;
 	static uint32_t cont_ok_tick = 0;
+	static uint32_t fd_on_last_cmd_ms = 0;
+	PowerSetpointTryResult_t psd_result;
+
+#if PSD_ENABLE
+	PowerSetpoint_UpdateDeliveryLatch();
+	if (PowerSetpoint_HasPending()) {
+		psd_result = PowerSetpoint_TryApply();
+		if (psd_result == PSD_TRY_START_FAST_DISCHARGE) {
+			PSU_SwitchState(PSU_FAST_DISCHARGE_OFF);
+		}
+	}
+#endif
 
 	// Обновляем ONLINE/READY по таймауту
 	if((HAL_GetTick() - can_lastpacket) > PSU_ONLINE_TIMEOUT){
+		if (PSU0.online) {
+			log_printf(LOG_WARN, "PSU CAN timeout age=%lums -> offline\n",
+			           (unsigned long)(HAL_GetTick() - can_lastpacket));
+		}
 		PSU0.online = 0;
 		PSU0.PSU_enabled = 0;
 		PSU_04.moduleTemperature = 0;
@@ -345,8 +533,9 @@ void PSU_Task(void){
 
 	case PSU_READY:
 		// модуль готов, но выключен
-		PSU0.hv_mode = 0;
-		PSU0.hv_tick = 0;
+		CONN.hv_limit = 0u;
+		CONN.hv_tick = 0u;
+		CONN.hv_limit_count = 0u;
 
 		RELAY_Write(RELAY_DC, 0);
 		if(!PSU0.ready){
@@ -403,6 +592,99 @@ void PSU_Task(void){
 		}
 		break;
 
+	case PSU_FAST_DISCHARGE_OFF:
+		if (!CONN.EnableOutput || !PSU0.ready || PSU0.cont_fault || PSU0.psu_fault) {
+			log_printf(LOG_WARN, "Fast discharge abort -> stop\n");
+			PowerSetpoint_OnFastDischargeAbort();
+			PSU_SwitchState(PSU_CURRENT_DROP);
+			break;
+		}
+		PSU_Enable(0, 0);
+		PSU_SwitchState(PSU_FAST_DISCHARGE_WAIT);
+		break;
+
+	case PSU_FAST_DISCHARGE_WAIT: {
+		PowerSetpoint_t fd_sp;
+
+		if (!CONN.EnableOutput || !PSU0.ready || PSU0.cont_fault || PSU0.psu_fault) {
+			log_printf(LOG_WARN, "Fast discharge abort -> stop\n");
+			PowerSetpoint_OnFastDischargeAbort();
+			PSU_SwitchState(PSU_CURRENT_DROP);
+			break;
+		}
+
+		/* Как PSU_WAIT_ACK_OFF: 0–20 V на телеметрии = модуль выключен */
+		if (!PSU0.PSU_enabled) {
+			PowerSetpoint_GetFastDischargeTarget(&fd_sp);
+			log_printf(LOG_INFO, "Fast discharge off ack, V=%u -> set %u\n",
+			           (unsigned)CONN.MeasuredVoltage, (unsigned)fd_sp.voltage_V);
+			PSU_SwitchState(PSU_FAST_DISCHARGE_SET);
+		} else if (PSU_StateTime() > PSD_OFF_TIMEOUT_MS) {
+			log_printf(LOG_WARN, "Fast discharge off timeout, V=%u\n",
+			           (unsigned)CONN.MeasuredVoltage);
+			PSU_FastDischarge_AbortToConnected();
+		}
+		break;
+	}
+
+	case PSU_FAST_DISCHARGE_SET: {
+		PowerSetpoint_t fd_sp;
+
+		if (!CONN.EnableOutput || !PSU0.ready || PSU0.cont_fault || PSU0.psu_fault) {
+			log_printf(LOG_WARN, "Fast discharge abort -> stop\n");
+			PowerSetpoint_OnFastDischargeAbort();
+			PSU_SwitchState(PSU_CURRENT_DROP);
+			break;
+		}
+		PowerSetpoint_GetFastDischargeTarget(&fd_sp);
+		PSU_SetVoltageCurrent(0, fd_sp.voltage_V, fd_sp.current_0p1A);
+		PSU_SwitchState(PSU_FAST_DISCHARGE_ON);
+		break;
+	}
+
+	case PSU_FAST_DISCHARGE_ON:
+		if (!CONN.EnableOutput || !PSU0.ready || PSU0.cont_fault || PSU0.psu_fault) {
+			log_printf(LOG_WARN, "Fast discharge abort -> stop\n");
+			PowerSetpoint_OnFastDischargeAbort();
+			PSU_SwitchState(PSU_CURRENT_DROP);
+			break;
+		}
+		PSU_Enable(0, 1);
+		fd_on_last_cmd_ms = HAL_GetTick();
+		PSU_SwitchState(PSU_FAST_DISCHARGE_ON_WAIT);
+		break;
+
+	case PSU_FAST_DISCHARGE_ON_WAIT: {
+		PowerSetpoint_t fd_sp;
+		uint16_t v_low;
+
+		if (!CONN.EnableOutput || !PSU0.ready || PSU0.cont_fault || PSU0.psu_fault) {
+			log_printf(LOG_WARN, "Fast discharge abort -> stop\n");
+			PowerSetpoint_OnFastDischargeAbort();
+			PSU_SwitchState(PSU_CURRENT_DROP);
+			break;
+		}
+		PowerSetpoint_GetFastDischargeTarget(&fd_sp);
+		v_low = (fd_sp.voltage_V > PSD_PRECHARGE_TOLERANCE_V) ?
+		        (uint16_t)(fd_sp.voltage_V - PSD_PRECHARGE_TOLERANCE_V) : 0u;
+
+		if (PSU0.PSU_enabled && CONN.MeasuredVoltage >= v_low) {
+			PowerSetpoint_OnFastDischargeComplete();
+			PSU_SwitchState(PSU_CONNECTED);
+		} else {
+			if ((HAL_GetTick() - fd_on_last_cmd_ms) >= PSD_ON_RETRY_MS) {
+				PSU_FastDischarge_PushTarget();
+				fd_on_last_cmd_ms = HAL_GetTick();
+			}
+			if (PSU_StateTime() > PSD_ON_TIMEOUT_MS) {
+				log_printf(LOG_WARN, "Fast discharge on timeout, V=%u (target %u)\n",
+				           (unsigned)CONN.MeasuredVoltage, (unsigned)fd_sp.voltage_V);
+				PSU_FastDischarge_AbortToConnected();
+			}
+		}
+		break;
+	}
+
 	case PSU_CURRENT_DROP:
 		// снижаем ток до нуля перед отключением DC
 		CONN.RequestedCurrent = 0;
@@ -449,6 +731,8 @@ void PSU_Task(void){
 		PSU_SwitchState(PSU_UNREADY);
 		break;
 	}
+
+	PSU_LogPeriodicDiag();
 }
 
 

Core/Src/serial.c

@@ -7,6 +7,7 @@
 #include "debug.h"
 #include "isr_opt.h"
 #include "psu_control.h"
+#include "power_setpoint_executor.h"
 #include "serial_control.h"
 #include <stdint.h>
 #include <string.h>
@@ -46,7 +47,6 @@ static uint8_t enabled = 0;
 static uint8_t pwm_duty_percent = 100;
 uint8_t isolation_enable = 0;
 static uint32_t last_host_seen = 0;
-static uint8_t fake_500_voltage_mode = 0;
 static uint8_t everest_timed_out = 0;
 static uint8_t everest_timeout_warn_latched = 0;
 static uint8_t everest_timeout_stop_latched = 0;
@@ -330,22 +330,41 @@ void CCS_SerialLoop(void) {
     }
 
     // 10s timeout: enforce safe-state until host communication recovers.
-    if (host_timeout_stop) {
-        CONN.EnableOutput = 0;
-        CCS_EvseState = Unknown;
-        CP_SetDuty(100);
-        if (CCS_ConnectorState != CCS_DISABLED && CCS_ConnectorState != CCS_UNKNOWN) {
-            CCS_ConnectorState = CCS_DISABLED;
-        }
-    } else {
-        if (last_cmd == CMD_STOP) {
+    {
+        static uint8_t prev_enable_output = 0xFFu;
+        uint8_t new_enable_output;
+
+        if (host_timeout_stop) {
             CONN.EnableOutput = 0;
-        } else {
-            CONN.EnableOutput = ev_enable_output ? 1 : 0;
-            if((CONN.EnableOutput == 0) && (CONN.connState == Preparing)){
-                CONN.EnableOutput = 0;
+            CCS_EvseState = Unknown;
+            CP_SetDuty(100);
+            if (CCS_ConnectorState != CCS_DISABLED && CCS_ConnectorState != CCS_UNKNOWN) {
+                CCS_ConnectorState = CCS_DISABLED;
             }
+            new_enable_output = 0u;
+        } else {
+            if (last_cmd == CMD_STOP) {
+                CONN.EnableOutput = 0;
+            } else {
+                CONN.EnableOutput = ev_enable_output ? 1 : 0;
+                if((CONN.EnableOutput == 0) && (CONN.connState == Preparing)){
+                    CONN.EnableOutput = 0;
+                }
+            }
+            new_enable_output = CONN.EnableOutput;
         }
+
+        if (prev_enable_output != 0xFFu && prev_enable_output != new_enable_output) {
+            log_printf(LOG_INFO,
+                       "EnableOutput %u->%u ev=%u stop=%u host_to=%u err=%u\n",
+                       (unsigned)prev_enable_output,
+                       (unsigned)new_enable_output,
+                       (unsigned)ev_enable_output,
+                       (unsigned)(last_cmd == CMD_STOP),
+                       (unsigned)host_timeout_stop,
+                       (unsigned)CONN.chargingError);
+        }
+        prev_enable_output = new_enable_output;
     }
 
     if ((cp_state_buffer == EV_STATE_B_CONN_PREP) ||
@@ -453,9 +472,6 @@ static void send_state(void) {
     CCS_State.DutyCycle = CP_GetDuty();
     CCS_State.OutputEnabled = PSU0.CONT_enabled;
     CCS_State.MeasuredVoltage = (uint16_t)CONN.MeasuredVoltage;
-    if (fake_500_voltage_mode) {
-        CCS_State.MeasuredVoltage = FAKE_EVREQ_VOLTAGE_V;
-    }
     CCS_State.MeasuredCurrent = (uint16_t)CONN.MeasuredCurrent;
     CCS_State.Power = CCS_Power;
     CCS_State.Energy = CCS_Energy;
@@ -533,15 +549,9 @@ ISR_FAST static void apply_command(uint8_t cmd, const uint8_t* payload, uint16_t
         }
         case CMD_E2M_SET_OUTPUT_VOLTAGE: {
             const e2m_set_output_t* p = (const e2m_set_output_t*)payload;
-            if (p->voltage_V == FAKE_EVREQ_VOLTAGE_V) {
-                fake_500_voltage_mode = 1u;
-                CONN.RequestedVoltage = FAKE_PSU_VOLTAGE_V;
-                CONN.WantedCurrent = FAKE_PSU_CURRENT_0P1A;
-            } else {
-                fake_500_voltage_mode = 0u;
-                CONN.RequestedVoltage = p->voltage_V;
-                CONN.WantedCurrent = p->current_0p1A;
-            }
+            CONN.RequestedVoltage = p->voltage_V;
+            CONN.WantedCurrent = p->current_0p1A;
+            PowerSetpoint_OnCommand(p->voltage_V, p->current_0p1A);
             break;
         }
         case CMD_E2M_ISOLATION_CONTROL: {

Core/Src/serial_handler.c

@@ -139,8 +139,9 @@ static void monitoring_data_callback(void) {
 	statusPacket.outputEnabled = CONN.outputEnabled;
 	statusPacket.chargingError = CONN.chargingError;
     statusPacket.connState = CONN.connState;
-    statusPacket.chargingElapsedTimeMin = 0;
-    statusPacket.chargingElapsedTimeSec = 0;
+    CONN_GetElapsedForMonitoring(
+        &statusPacket.chargingElapsedTimeMin,
+        &statusPacket.chargingElapsedTimeSec);
     statusPacket.estimatedRemainingChargingTime = 0;
 
     // состояние зарядной станции

Debug/Core/Src/charger_control.cyclo

@@ -1,3 +1,4 @@
 ../Core/Src/charger_control.c:11:6:CONN_Init	1
-../Core/Src/charger_control.c:19:6:CONN_Loop	7
-../Core/Src/charger_control.c:42:6:CONN_SetState	16
+../Core/Src/charger_control.c:23:6:CONN_Loop	10
+../Core/Src/charger_control.c:56:6:CONN_GetElapsedForMonitoring	3
+../Core/Src/charger_control.c:66:6:CONN_SetState	16

Debug/Core/Src/subdir.mk

@@ -17,6 +17,8 @@ C_SRCS += \
 ../Core/Src/gpio.c \
 ../Core/Src/main.c \
 ../Core/Src/meter.c \
+../Core/Src/power_setpoint_executor.c \
+../Core/Src/power_setpoint_policy.c \
 ../Core/Src/psu_control.c \
 ../Core/Src/rgb_controller.c \
 ../Core/Src/rtc.c \
@@ -46,6 +48,8 @@ C_DEPS += \
 ./Core/Src/gpio.d \
 ./Core/Src/main.d \
 ./Core/Src/meter.d \
+./Core/Src/power_setpoint_executor.d \
+./Core/Src/power_setpoint_policy.d \
 ./Core/Src/psu_control.d \
 ./Core/Src/rgb_controller.d \
 ./Core/Src/rtc.d \
@@ -75,6 +79,8 @@ OBJS += \
 ./Core/Src/gpio.o \
 ./Core/Src/main.o \
 ./Core/Src/meter.o \
+./Core/Src/power_setpoint_executor.o \
+./Core/Src/power_setpoint_policy.o \
 ./Core/Src/psu_control.o \
 ./Core/Src/rgb_controller.o \
 ./Core/Src/rtc.o \
@@ -99,7 +105,7 @@ Core/Src/%.o Core/Src/%.su Core/Src/%.cyclo: ../Core/Src/%.c Core/Src/subdir.mk
 clean: clean-Core-2f-Src
 
 clean-Core-2f-Src:
-	-$(RM) ./Core/Src/adc.cyclo ./Core/Src/adc.d ./Core/Src/adc.o ./Core/Src/adc.su ./Core/Src/board.cyclo ./Core/Src/board.d ./Core/Src/board.o ./Core/Src/board.su ./Core/Src/can.cyclo ./Core/Src/can.d ./Core/Src/can.o ./Core/Src/can.su ./Core/Src/charger_control.cyclo ./Core/Src/charger_control.d ./Core/Src/charger_control.o ./Core/Src/charger_control.su ./Core/Src/cp.cyclo ./Core/Src/cp.d ./Core/Src/cp.o ./Core/Src/cp.su ./Core/Src/crc.cyclo ./Core/Src/crc.d ./Core/Src/crc.o ./Core/Src/crc.su ./Core/Src/debug.cyclo ./Core/Src/debug.d ./Core/Src/debug.o ./Core/Src/debug.su ./Core/Src/dma.cyclo ./Core/Src/dma.d ./Core/Src/dma.o ./Core/Src/dma.su ./Core/Src/fire_alarm.cyclo ./Core/Src/fire_alarm.d ./Core/Src/fire_alarm.o ./Core/Src/fire_alarm.su ./Core/Src/gpio.cyclo ./Core/Src/gpio.d ./Core/Src/gpio.o ./Core/Src/gpio.su ./Core/Src/main.cyclo ./Core/Src/main.d ./Core/Src/main.o ./Core/Src/main.su ./Core/Src/meter.cyclo ./Core/Src/meter.d ./Core/Src/meter.o ./Core/Src/meter.su ./Core/Src/psu_control.cyclo ./Core/Src/psu_control.d ./Core/Src/psu_control.o ./Core/Src/psu_control.su ./Core/Src/rgb_controller.cyclo ./Core/Src/rgb_controller.d ./Core/Src/rgb_controller.o ./Core/Src/rgb_controller.su ./Core/Src/rtc.cyclo ./Core/Src/rtc.d ./Core/Src/rtc.o ./Core/Src/rtc.su ./Core/Src/serial.cyclo ./Core/Src/serial.d ./Core/Src/serial.o ./Core/Src/serial.su ./Core/Src/serial_control.cyclo ./Core/Src/serial_control.d ./Core/Src/serial_control.o ./Core/Src/serial_control.su ./Core/Src/serial_handler.cyclo ./Core/Src/serial_handler.d ./Core/Src/serial_handler.o ./Core/Src/serial_handler.su ./Core/Src/sma_filter.cyclo ./Core/Src/sma_filter.d ./Core/Src/sma_filter.o ./Core/Src/sma_filter.su ./Core/Src/soft_rtc.cyclo ./Core/Src/soft_rtc.d ./Core/Src/soft_rtc.o ./Core/Src/soft_rtc.su ./Core/Src/stm32f1xx_hal_msp.cyclo ./Core/Src/stm32f1xx_hal_msp.d ./Core/Src/stm32f1xx_hal_msp.o ./Core/Src/stm32f1xx_hal_msp.su ./Core/Src/stm32f1xx_it.cyclo ./Core/Src/stm32f1xx_it.d ./Core/Src/stm32f1xx_it.o ./Core/Src/stm32f1xx_it.su ./Core/Src/syscalls.cyclo ./Core/Src/syscalls.d ./Core/Src/syscalls.o ./Core/Src/syscalls.su ./Core/Src/sysmem.cyclo ./Core/Src/sysmem.d ./Core/Src/sysmem.o ./Core/Src/sysmem.su ./Core/Src/system_stm32f1xx.cyclo ./Core/Src/system_stm32f1xx.d ./Core/Src/system_stm32f1xx.o ./Core/Src/system_stm32f1xx.su ./Core/Src/tim.cyclo ./Core/Src/tim.d ./Core/Src/tim.o ./Core/Src/tim.su ./Core/Src/usart.cyclo ./Core/Src/usart.d ./Core/Src/usart.o ./Core/Src/usart.su
+	-$(RM) ./Core/Src/adc.cyclo ./Core/Src/adc.d ./Core/Src/adc.o ./Core/Src/adc.su ./Core/Src/board.cyclo ./Core/Src/board.d ./Core/Src/board.o ./Core/Src/board.su ./Core/Src/can.cyclo ./Core/Src/can.d ./Core/Src/can.o ./Core/Src/can.su ./Core/Src/charger_control.cyclo ./Core/Src/charger_control.d ./Core/Src/charger_control.o ./Core/Src/charger_control.su ./Core/Src/cp.cyclo ./Core/Src/cp.d ./Core/Src/cp.o ./Core/Src/cp.su ./Core/Src/crc.cyclo ./Core/Src/crc.d ./Core/Src/crc.o ./Core/Src/crc.su ./Core/Src/debug.cyclo ./Core/Src/debug.d ./Core/Src/debug.o ./Core/Src/debug.su ./Core/Src/dma.cyclo ./Core/Src/dma.d ./Core/Src/dma.o ./Core/Src/dma.su ./Core/Src/fire_alarm.cyclo ./Core/Src/fire_alarm.d ./Core/Src/fire_alarm.o ./Core/Src/fire_alarm.su ./Core/Src/gpio.cyclo ./Core/Src/gpio.d ./Core/Src/gpio.o ./Core/Src/gpio.su ./Core/Src/main.cyclo ./Core/Src/main.d ./Core/Src/main.o ./Core/Src/main.su ./Core/Src/meter.cyclo ./Core/Src/meter.d ./Core/Src/meter.o ./Core/Src/meter.su ./Core/Src/power_setpoint_executor.cyclo ./Core/Src/power_setpoint_executor.d ./Core/Src/power_setpoint_executor.o ./Core/Src/power_setpoint_executor.su ./Core/Src/power_setpoint_policy.cyclo ./Core/Src/power_setpoint_policy.d ./Core/Src/power_setpoint_policy.o ./Core/Src/power_setpoint_policy.su ./Core/Src/psu_control.cyclo ./Core/Src/psu_control.d ./Core/Src/psu_control.o ./Core/Src/psu_control.su ./Core/Src/rgb_controller.cyclo ./Core/Src/rgb_controller.d ./Core/Src/rgb_controller.o ./Core/Src/rgb_controller.su ./Core/Src/rtc.cyclo ./Core/Src/rtc.d ./Core/Src/rtc.o ./Core/Src/rtc.su ./Core/Src/serial.cyclo ./Core/Src/serial.d ./Core/Src/serial.o ./Core/Src/serial.su ./Core/Src/serial_control.cyclo ./Core/Src/serial_control.d ./Core/Src/serial_control.o ./Core/Src/serial_control.su ./Core/Src/serial_handler.cyclo ./Core/Src/serial_handler.d ./Core/Src/serial_handler.o ./Core/Src/serial_handler.su ./Core/Src/sma_filter.cyclo ./Core/Src/sma_filter.d ./Core/Src/sma_filter.o ./Core/Src/sma_filter.su ./Core/Src/soft_rtc.cyclo ./Core/Src/soft_rtc.d ./Core/Src/soft_rtc.o ./Core/Src/soft_rtc.su ./Core/Src/stm32f1xx_hal_msp.cyclo ./Core/Src/stm32f1xx_hal_msp.d ./Core/Src/stm32f1xx_hal_msp.o ./Core/Src/stm32f1xx_hal_msp.su ./Core/Src/stm32f1xx_it.cyclo ./Core/Src/stm32f1xx_it.d ./Core/Src/stm32f1xx_it.o ./Core/Src/stm32f1xx_it.su ./Core/Src/syscalls.cyclo ./Core/Src/syscalls.d ./Core/Src/syscalls.o ./Core/Src/syscalls.su ./Core/Src/sysmem.cyclo ./Core/Src/sysmem.d ./Core/Src/sysmem.o ./Core/Src/sysmem.su ./Core/Src/system_stm32f1xx.cyclo ./Core/Src/system_stm32f1xx.d ./Core/Src/system_stm32f1xx.o ./Core/Src/system_stm32f1xx.su ./Core/Src/tim.cyclo ./Core/Src/tim.d ./Core/Src/tim.o ./Core/Src/tim.su ./Core/Src/usart.cyclo ./Core/Src/usart.d ./Core/Src/usart.o ./Core/Src/usart.su
 
 .PHONY: clean-Core-2f-Src