Moved firmware to subfoler firmware

.gitignore

@@ -7,3 +7,5 @@
 *.map
 /Debug/
 /Release/
+/firmware/Debug/
+/firmware/Release/

firmware/.settings/language.settings.xml

@@ -5,7 +5,7 @@
 			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
 			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
 			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
-			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="892067782257261287" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-1730349911864528736" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
 				<language-scope id="org.eclipse.cdt.core.gcc"/>
 				<language-scope id="org.eclipse.cdt.core.g++"/>
 			</provider>
@@ -16,7 +16,7 @@
 			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
 			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
 			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
-			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="892067782257261287" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-1730349911864528736" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
 				<language-scope id="org.eclipse.cdt.core.gcc"/>
 				<language-scope id="org.eclipse.cdt.core.g++"/>
 			</provider>

firmware/BMS_v3 Debug.cfg

@@ -0,0 +1,42 @@
+# This is an genericBoard board with a single STM32F107VCTx chip
+#
+# Generated by STM32CubeIDE
+# Take care that such file, as generated, may be overridden without any early notice. Please have a look to debug launch configuration setup(s)
+
+source [find interface/stlink-dap.cfg]
+
+
+set WORKAREASIZE 0x8000
+
+transport select "dapdirect_swd"
+
+set CHIPNAME STM32F107VCTx
+set BOARDNAME genericBoard
+
+# Enable debug when in low power modes
+set ENABLE_LOW_POWER 1
+
+# Stop Watchdog counters when halt
+set STOP_WATCHDOG 1
+
+# STlink Debug clock frequency
+set CLOCK_FREQ 8000
+
+# Reset configuration
+# use hardware reset, connect under reset
+# connect_assert_srst needed if low power mode application running (WFI...)
+reset_config srst_only srst_nogate connect_assert_srst
+set CONNECT_UNDER_RESET 1
+set CORE_RESET 0
+
+# ACCESS PORT NUMBER
+set AP_NUM 0
+# GDB PORT
+set GDB_PORT 3333
+
+
+
+# BCTM CPU variables
+
+source [find target/stm32f1x.cfg]
+