AkbMonitorScreen Serial number Battery charge level, % Number of modules Battery voltage, V Number of cells Nominal capacity, A/h Actual capacity, A/h Battery temperature, °C BMS temperature, °C Maximum cell voltage, V Minimum cell voltage, V Current BMSInterface Reconnect No ports found Please specify the connection manually the first time you are connecting. Not connected Connected (serial) to %1 Connected (TCP) to %1:%2 Connected (BLE) to %1 , limited mode Invalid serial port: %1 Serial port is not writable Connect serial Serial port support is not enabled in this build of ENNOID-BMS Tool. Serial port error: TCP Error No firmware read response Read Firmware Version Could not read firmware version. Make sure that selected port really belongs to the ENNOID-BMS. Not Supported Firmwares This version of ENNOID-BMS Tool does not seem to have any supported firmwares. Something is probably wrong with the BMS configuration file. Error The firmware on the connected ENNOID-BMS is too old. Please update it using a programmer. Warning The connected ENNOID-BMS has newer firmware than this version of the ENNOID-BMS Tool supports. It is recommended that you update the ENNOID-BMS Tool to the latest version. Alternatively, the firmware on the connected ENNOID-BMS can be downgraded in the firmware page. Until then, limited communication mode will be used where only the firmware can be changed. The connected ENNOID-BMS has too old firmware. Since the connected ENNOID-BMS has firmware with bootloader support, it can be updated from the Firmware page. Until then, limited communication mode will be used where only the firmware can be changed. Firmware version: %1.%2, Hardware: %3, UUID: %4 BMS configuration updated BMS configuration stored to Flash BmsServiceScreen Terminal Firmware update Network settings Time settings BmsSettingsScreen Serial number Configuration Number of boards Number of cells # SOC Number of cells connected in parallel Battery capacity Limits Maximum charge current, A Maximum load current, A Maximum temperature, °C Cell configuration Lower disable threshold, V Upper disable threshold, V Lower enable threshold (should be higher than disable), V Balancing configuration Balancing start voltage, V Cell voltage delta to start balancing, V Cell balancing interval, ms Current configuration Current factor K1 Current factor K2 Output settings # 1 # 2 Active Brush control Shunt charging contactor SOC threshold, % Delay, s # 3 Cooling activation # 4 Heating activation BMS configuration saved to file Read default settings The settings are written to non-volatile memory. Wait, please. Closes at t<, °C Use to control charger Opens at t>, °C Current sensor value "0" BMS sensors mask for master board BMS sensors mask for slave board # Battery sensors mask for master board Battery sensors mask for slave board # Upper enable threshold (should be lower than disable), V Calibrate "0" Load settings from file Select configuration file Configuration files (*.xml) All files (*) Save settings to file Read current settings from BMS Write to non-volatile memory of BMS Write current values to BMS CanSettingsScreen CAN availability state External CAN Charging CAN Apply CellMonitorScreen # Voltage Balancing V Commands BMS configuration is set Network settings applied successfully Buffer erase Buffer erase timeout CRC/Size write CRC/Size write timeout Firmware data write Firmware data write timeout Firmware update completed! Reconnect to the board if you want to continue working with it. System ok Pack overvoltage Pack undervoltage Load overvoltage Load undervoltage Charger overvoltage Charger undervoltgae Cell hard overvoltage Cell hard undervoltage Cell soft overvoltage Cell soft undervoltage Too high or too low voltage Too high or too low temperature Over current Over temperature BMS Under temperature BMS Discharge over temperature cell Discharge under temperature cell Charge over temperature cell Charge under temperature cell Precharge timeout Discharge retry Charge retry Unknown state Cancelled ConfigParams OK tag %1 not found Could not open %1 for writing Could not open %1 for reading ConnectionDialog Connection screen Select serial port Connect Disconnect DebugInformationScreen Clear FirmwareUpdateHelper Upload error Could not open file. Make sure that the path is valid. FirmwareUpdateScreen Board information Firmware Hardware UUID Upload firmware Select firmware file Firmware files (*.bin) All files (*) MainWindow Cubo Verde BMS Hide menu AKB monitor Cell monitor Temperature monitor Configuration Visualization History BMS service Connection BMS settings Information output Disconnected Serial number Connected Firmware update Tool started MessageDialog Ok NetworkSettingsScreen Url 1 Url 2 APN User Password Default Apply QObject Autoconnect Could not autoconnect. Make sure that the USB cable is plugged in and that the ENNOID-BMS is powered. TemperatureMonitorScreen Minimum battery temperature, °C Minimum BMS temperature, °C Average battery temperature, °C Average BMS temperature, °C Maximum battery temperature, °C Maximum BMS temperature, °C Sensors for master board Sensors for slave board # Sensor # TerminalScreen Clear Send Help TimeSettingsScreen Date Time Day Month Year January February March April May June July August September October November December Hour Minute Second Read from board Read from computer Write to board Time settings applied successfully Translator EN RU IT Utility ENNOID-BMS Tool V%1 © Kevin Dionne 2019 <a href="mailto:kevin.dionne@ennoid.me">kevin.dionne@ennoid.me</a> <a href="https://www.ennoid.me/">https://www.ennoid.me/</a> Based on: DieBieMS-tool DieBieMS Tool © Danny Bokma 2018 <a href="mailto:bms@diebie.nl">bms@diebie.nl</a> <a href="https://diebie.nl/">https://diebie.nl/</a> Based on: VESC-tool VESC Tool © Benjamin Vedder 2018 <a href="mailto:benjamin@vedder.se">benjamin@vedder.se</a> <a href="https://vesc-project.com/">https://vesc-project.com/</a> VisualizationScreen Voltage Current Battery temperature BMS temperature Cell voltage Cell list Time, s Voltage, V s V Current, A A Temperature, °C °C Pause data collection Resume data collection Clear data Reset zoom Interval, s Cell # Voltage indicator Current indicator Maximum temperature Average temperature Minimum temperature Maximum voltage Average voltage Minimum voltage